Teledu 10pcs Front Tie Rod Ends Ball Joints For B2500 B3000 Explorer Mountaineer Ranger

This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the socalled tie rodNote Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance1.Lift the vehicle and dismount the front axle wheels2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes3.Dismount the front underride guard4.Loosen the fastening nut from the tie rod and remove it completely5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator6.Remove the clamp of the bellow on the steering gear7.Push the bellow towards the tie rod end8.Unscrew the inner tie rod from the rack9.Clean the sealing face of the bellow at the steering gear10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckleNoteAlways use new selflocking nuts and bolts for a reliable repair11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer12.Mount the bellow and close the clamps with the appropriate special toolNoteIncorrect mounting of the bellow can lead to corrosion of the rack the steering gear starts leaking which can lead to a failure in the steering assistance13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturerNoteDuring mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure14.Mount the front underride guard15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications17.Perform a test driveFrequently Asked Questions1.Do I need to replace the control arm if the bushings are worn2.What happens if a ball joint breaksWhen a ball joint breaks, you will hear a mysterious noise inside your car wheelYour car tire will wearout since your alignment will be broken, and you will feel the car getting out of controlIf the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be seriousBroken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car3.What happens if I dont replace ball joints4.Do I?need to grease new ball jointsI would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new 1 after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card5.Why should I get my tie rods inspected on a regular basis6.Vibrations7.Shaking8.Wandering9.What are the symptoms of a bad sway bar10.What happens when a sway bar breaks Brand Unbrand Manufacturer Part Number E81121201CP Interchange Part Number K80012 K8695T ES3461 EV317 K7275 Placement on Vehicle Left, Right, Front Surface Finish Premium Quality Greasable or Sealed Greasable CountryRegion of Manufacture China OEOEM Part Number F57Z3050BB, F5TZ3078A, F5TZ3079A, F65Z3078EJ Items Included Mounting Hardware Warranty Period 1 Year warranty Kit Included 10PCS Kit Parts Included Ball Joint, Sway Bar,Outer Tie Rod, Inner Tie Rod Kit or Single Part Kit Cross Reference Part Number1 1995 1996 1997 1998 1999 2000 2001 2002 Cross Reference Part Number2 2003 2004 2005 2006 2007 2008 2009 2010 2011 Bundle Listing Yes Adjustable Yes Universal Fitment No Type Sway Bar Link Features Greasable